Breeding Tank:
small tank (I use 5 l/2 gallon) with approximately no more than 4-5 inches of "conditioned" water; a corner sponge filter; submersible heater set at 80; a plastic lid or piece of Styrofoam cup cut for the bubblenest; ...
Breeding Tank & Maintenance:
Tank: 18"x 8"x 8" with a small glass trough 8"x 2"x 2" placed to one side of the tank. This contained silver sand and was planted with Indian Fern.
Breeding Tank: An aquarium set up for the breeding of fish.
Brine Shrimp: Also known as Artemia and sea monkeys. Brine Shrimps are a very common food for fresh and marine water fish.
Breeding tank size = 450 x 200 x 150mm. Water Temp. =76 deg F. Ph =7.2 GH = 6 spawning. Followed the typical ''T'' formation two days after a water change which reduced the temp. by 6deg F.
Breeding tank : Some prefer to use a separate tank for breeding or simply keeping their female mouthbrooding cichlids till the fry is big enough to survive alone. This tank should have some hiding places and gravel on the bottom.
"Breeding Tank" - small tank with approximately 4-5 inches of water, a corner sponge filter, submersible heater set at 80, a plastic lid or piece of styrofoam cup cut for the bubblenest and plastic plants so female can hide when needed.
A breeding tank should be set up with abundant floating plants and dim lighting. Setting the tank up without substrate will make thee tank easier to keep clean while raising the fry. Males can be identified by their longer fins and lack of red color.
A breeding tank also is good because it can be kept clean. Eggs and fry need very clean water to hatch and grow. There are also no adults around to compete with the babies for food.
The breeding tank should be at least 18 inches in height, and have a capacity not less than 20 gallons as an absolute minimum. 30 gallons is better, as it allows space to start growing out the fry as well.
A: A breeding tank will help raise the survival rate of the fry. Once born, the fry risk getting eaten by adults who would immediately see them as tasty live food.
Q: When should I return the female to the community tank?
In my breeding tanks I combine a lot of plants with a few caves that are situated on the edges of open areas in the tank. I generally try to set up only one cave site for a pair and two or three for a trio.
Use a small breeding tank with fine-leaved plants. Eggs will be scattered among the plants. The fry will hatch in around 24-30 hours.
Comments
This is one of a complex of species sometimes known as "Blood Tetras" or "Blood Characins".
A Corydoras breeding tank should be long enough. As a rule of thumb, length of the tank should be at least ten times the maximum size of the adult fish.
Breeding:A large breeding tank is required, with dark soil, peat filtration and soft(under 4KH)acidic water. Lots of plants, in between which the fish will lay their eggs.
Breeding: In larger breeding tanks(1m) lower the waterlevel to 20-25 cm, densely planted sides and some free swimming space. Add a female to the tank for a few days, and add a male in the evening(best on friday!).
A female guppy was very pregnent, so in she went into the breeding tank. At this point, the breeding tank had one male and two female gouramies as well as one female guppy and five baby guppies.
I set up a 50 gallon breeding tank for them. About nine months later, in their new tank, they had grown to about five inches in body size. By this time I was getting very discouraged because the fish were not pairing off.
Once the pair has been chosen, keep them isolated from each other for a couple of weeks before placing them into the breeding tank. Condition them with plenty of a good variety of live and frozen foods during this time.
Breeding/Reproduction: A breeding tank should be set up with a sponge filer and either many fine leaved plants or a spawning mop. A pair of healthy adult rainbowfish should be introduced.
The pair can be introduced into a breeding tank after two or three weeks. For most species a 20" (50 cm) or 10 gallon (38 L) breeding tank should do.
Once spawning is completed the male will chase the female out of the cave, and if a breeding tank was used return the female(s) to the normal tank.
Pairs can be removed to individual, 29 gallon breeding tanks before they begin to chase and stress other Blue Discus kept in their enclosures. A clean piece of slate leaned at a 65 degree angle to the tank wall should be offered.
When you want to set up a tropical fish breeding program you will have to set up a breeding tank. You will have to be extremely vigilant about maintaining an optimal water temperature.
A breeding tank can be easily set up and the fish induced to spawn throughout the year. Although, some aquarists have found this species has been a difficult challenge to successfully raise the newly hatched larvae.
Submersible heaters are useful in breeding tanks where the water level has been lowered and an upright heater cannot operate. The Visi-Therm Deluxe by Marineland, with its easy to read temperature dial, is a favorite.
The set-up pairs generally do not spawn until several days after being placed in the breeding tank, usally before daybreak, usally in the evening hours. Spawning is usally triggered by a fise in atmospheric pressure.
For breeding a breeding tank needs to be set up (5 gallons is fine) and the PH lowered to 5.5 and the hardness of the water to 4 dGH.
This fish was BRED by us humans in aquariums or large-scale breeding tanks, with the specific goal of being sold to someone who hopes to obtain satisfaction in keeping a fish in the home aquarium, ...
A breeding tank is ideal with a 2-3 inch layer of peat at the bottom. The fish will bury the eggs in the peat. After spawning, remove the peat that contain the eggs and press out any excess water.
An egg layer, the Western Splendid Rainbow reproduces more easily in a separate breeding tank with a moss substrate. Courtship begins with the male displaying his brightest colors. At a temperature of 75°F, the fry will hatch after six or seven days.
The Balloon Molly is a livebearer that requires a spawning box in a 25 gallon, or larger, breeding tank. The aquarium should be planted as densely as possible or have a thick algae mat.
Spawning site may be a leaf, tank wall, filter tube, flat rock or wood, or in breeding tanks a piece of slate; the parents will guard the eggs and fry, fanning the eggs and picking out infertile ones.
Many breeding tanks, hospital tanks, and tanks used to raise fry use a bare bottom. It makes it easy to catch fish, it is easy to tear down, and it is very easy to clean.
I keep the smaller Nothobranchius species in breeding tanks of 30x20x20cm size (tap water pH 7.8, GH 22 and KH 18). These water specifications have emerged as optimal for most species. I feed (almost) exclusively frozen red mosquito larvae.
Breeding: Place fish in pairs(or one male with two females)into a breeding tank. After spawning remove parents from tank.
Tank Conditions: Temperature: 71.6 to 77 F. 15dH and a pH of 7.Tank bed of fine gravel, sand, pebbles, or glass marbles.
To breed them and save the largest amount of fry, put the male and female in a 10 gallon breeding tank. Add some java moss on the bottom and some duckweed on the surface. The tank is best filtered by a corner sponge filter.
Due to this, corner filters are very useful for tanks(ie shrimp breeding tanks) that need to keep the temperature cool.
While some aquarists maintain aquaria with minimal or no decoration, these are often breeding tanks or tanks for growing out fry. Most fish, however, do not show their best colors and behavior when kept in bare tanks, where they feel exposed.
Spawning cherry barbs is easy except that the parents tend to eat their eggs, so plants or artificial spawning mops must be very thick in the breeding tank.
Floating plants are particularly useful in aquariums with very shy fish that like to hide and in breeding tanks where fry need protection.
In many cases the breeding tank is the same as the grow out aquarium. After the fish have spawned and fertilized the eggs or dropped their babies, the parents can be removed and allow the fry to grow out.
They are expensive; $80 would buy a nice power filter, let you set up that extra breeding tank, or buy some very nice fish, but what's the point if you aren't around to enjoy it.
Filters: These are simple air or water pump operated filters that drive water through a porous cellulose sponge which is a great media for cultivating beneficial bacteria. These filters are typically used in smaller aquaria, or in breeding tanks ...
I use one square-inch of leaf per half-gallon of water for individual fish. One leaf per 10-gallon rearing tank for the fry. One-leaf per half-filled 10-gallon breeding tank.
Often, a breeding tank is provided with live plants and a grate to allow hiding places and places for spawning. A temperature around 82 degrees Fahrenheit (28 degrees Celsius) is maintained.
in color, only showing its best in old water in a well-planted aquarium, in not too much light. Live food is important to it. Like the other Aphyosemion the parents should be conditioned on live foods before placing them in a breeding tank.
The rearing tank should have the same water chemistry as the breeding tank - a water exchange between the two tanks prior to moving the eggs will help ensure this.
There are reports that direct sunlight in the breeding tank may help to stimulate spawning. The pair will produce up to 300 eggs, which will hatch in about 36 hours. The fry can be successfully reared on freshly hatched brine shrimp.
 See also: Fish, Water, Aquarium, Fry, Spawn
|
