Lath and plaster
From the early eighteenth until the mid twentieth century, ceilings were usually made using lath and plaster techniques (see right).
Lath and plaster removal
Lath and plaster is an old type of interior finish that's found in most homes built before World War II. The most common type of lath is wood, though metal lath is also found (and is more difficult to remove).
Lath and Plaster: The most common wall finish prior to the introduction of drywall. Thin wood strips (lath) were nailed onto the framing as a base for the sand/lime plaster.
Lattice: A framework of crossed wood or metal strips.
Lath and plaster Thin strips of wood nailed to interior surfaces such as studs and ceiling joists and covered with plaster Leadlight Decorative glazing using small rectangular, diamond or other shaped pieces of glass, often coloured, ...
Lath and Plaster Membrane
1. A thin slab of lath and plaster including any integral supporting and stiffening members. 2. Lath and plaster as a unit of structure.
Lath, Expanded Metal ...
What Is Lath and Plaster?
What Are the Best Tips for Installing Basement Drywall?
What Is Skim Coating?
The end effect is same as a lath and plaster wall. The performance is superior to covering stucco with drywall because it will not leave a void where uncontrolable-controllable bug and mold can grow. Costs are considerably less.
FINISHES - term includes lath and plaster, gypsum wallboard, tile, terrazzo, acoustical treatments, ceiling suspension systems, wood flooring,
resilient carpeting, special flooring, floor treatments, special coatings, painting and wallcoverings.
Axe: Just the trick for cutting through lath and plaster. Good luck trying to do this with a crowbar or sledge hammer. Again, preference for long hammer and larger heads.
Hatchet: Only briefly used but it did come in handy when it was needed.
The back side of the wall had been gutted for a room remodel project, so cutting the wood lath and plaster was easy... with the right tools.
Part 2 - Changes At The Main Breaker Panel ...
Small pry bar
Reciprocating saw, to cut any lath and plaster and to remove any obtrusive studs
Circular saw, to cut the 2x4 blocking
Drill/driver, fitted with a 1"8-inch drill bit
Caulk gun
Paintbrush ...
So it's no wonder that, since the 1940s, drywall has steadily replaced lath and plaster. The only wonder is that people still think it's tough to finish. It's not. To produce pro-quality walls and ceilings, go easy on the compound.
Studwork: A type of partition formed from studs at close intervals, traditionally clad with lath and plaster, now with plasterboard ...
strapping (fond de clouage, m.) A general term for battens fixed to the faces of walls as a support for lath and plaster or other cladding. See also furring.
earth, had tied a noose to the ceiling fixture in the middle of the room, then he put a couple boxes on the dining room table, climbed on the boxes, put his neck in the noose, and kicked the boxes away. His weight pulled the whole lath and plaster ...
Selection of limiting heights and spans are frequently based on minimum code requirements and accepted industry practice as follows: (a) L/120 for gypsum panel surfaces and veneer plaster finish surfaces, (b) L/240 for conventional lath and plaster ...
Wattle and daub - in days gone by was a latticework of wooden stakes called wattles that was daubed with a mixture of clay, sand and sometimes animal dung and straw to create a structure. This is similar to modern use of lath and plaster.
The studs transmit vertical forces (loads) from the roof and/or floor above to, ultimately, the foundation of the house. The studs also provide something to which to attach the exterior wall sheathing and interior wall finish (e.g., lath and plaster ...
 See also: Lath, Wall, Building, Walls, Construction
|
