Sole plate

Sole plate: A timber placed on the floor as the base for a partition
Special (brick): A brick specially made in a non-standard shape.
Special foundations: Defined, in the Party Wall act, as foundations incorporating steel.

Sole plate- The bottom, horizontal framing member of a wall that's attached to the floor sheeting and vertical wall studs.

Sole Plate: Bottom horizontal member of a frame wall.
Solid Bridging: A solid member placed between adjacent floor joists near the center of the span to prevent joists from twisting.

sole plate (lisse d'assise, f.) Bottom plate in timber framing.
solenoid valve (vanne électromagnétique, f.) A valve which is electrically operated.

SOLE PLATE - The bottom wood member of a framed stud wall.
SOLID BRIDGING - A short wood member placed between the floor joists at the center to prevent the joists from twisting.

Sole Plate: Bottom horizontal member of a frame wall.
Spalling: Condition of concrete when small pieces are breaking off due to wear, use of salt, or other reasons.

Sole Plate - See Bottom Plate.
Square Footage, Living - The square footage in a home that is heated and/or cooled. The space occupied by two-story rooms and stairwells is counted once in the lower floor's square footage.

SOLE PLATE - bottom horizontal member of a frame wall.
SPALLING - The chipping or flaking of concrete, bricks, or other masonry where improper drainage or venting and freeze/thaw cycling exists.

SOLE PLATE: The horizontal framing member directly under the studs.
SPACKLE: To cover wallboard joints with plaster.
SPAN: Horizontal distance between supports for joists, beams, or trusses.

SOLE PLATE: The horizontal framing member directly under the studs.
SPACING: The distance between two structural members.
SPACKLE: To cover wallboard joints with plaster.

Sole Plate: The lowest horizontal member on wall and partition framing (see sill).

Sole, sole plate: See Plate, sole.
Solid bridging: A solid member placed between adjacent floor joists near the center of the span to prevent joists from twisting.
Spalling: Cracking or flaking that develops on a concrete surface.

Sole Plate:
The sole plate is the bottom of the saw which seats on the surface being cut, it usually has a turned up lip around the edge so that it can move smoothly over the work surface.

Sole Plate
The bottom horizontal structural member of a stud framed wall.
Spacer Blocks
Short 2x4 or 2x6 blocks nailed to corner studs. A wall stud is nailed to the spacers that creates a new nailing surface.

Sole plate The horizontal member of a frame wall resting on the rough floor, to which the studs are nailed.
Span The horizontal distance between supports for joists, beams, or trusses.

sole plate--The bottom horizontal piece in a frame wall, usually single or double 2x4's. The wall is nailed into the deck or rough floor through the sole plate.

Sole Plate
The horizontal piece of dimension lumber to which the bottom of the studs are attached in a wall of a light frame building.
Sole Proprietor ...

Bottom or sole plate
The bottom framing member of a wall, usually either 2 x 4 or 2 x 6. The plate is nailed to the bottom of the studs and to the floor joist or sheathing below it.
Bow ...

The bottom member of a wall is the sole plate and the top member is the rafter plate.
Plenum - A chamber that serves as an air distribution area for heating or cooling systems. Generally placed between a false ceiling and the actual ceiling.

the sill or sole plate will stop on either side at the width of the rough opening for the door. The first studs on either side, the jack studs, go only as high as the rough opening of the doorway. On top of those go a double header.

They support the header and run down to the sole plate.
Jamb - A vertical member at the side of a window frame, or the horizontal member at the top of the window frame, as in head jamb.

Bring your "home run" wire up through the sole plate and out the access hole. Pull enough wire out to go past the first receptacles or switch outlet.

An older style of framing in which the studs in the bearing walls are run uninterrupted from the sole plate up to the roof plate. The floor joists are nailed to the studs.

Sill plate- A horizontal member anchored to a concrete or masonry wall.
Sole plate- Bottom horizontal member of a frame wall.
Top plate- Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members.
Plan view ...

In either case, it's typical to find the bottom plate of the stud wall (also called the sole plate) directly above concrete.

Also called the 'sole plate'.
Brace- An inclined piece of framing lumber applied to wall or floor to strengthen the structure. Often used on walls as temporary bracing until framing has been completed.

The vertical "2 X's" frame lumber (left and right) of a window or door opening, and runs continuously from the bottom sole plate to the top plate.
Knot
In lumber, the portion of a branch or limb of a tree that appears on the edge or face of the piece.

Sill plate, A horizontal member anchored to a concrete or masonry wall.
Sole plate, Bottom horizontal member of a frame wall.
Top plate, Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members.

Related Searches penny nails air infiltration knee wall scrap piece attic floor sole plate
Explore Home Renovations
Must Reads ...

Plate " Normally a horizontal member within a framed structure, such as: (1) sill plate " a horizontal member anchored to a concrete or masonry wall; (2) Sole plate " bottom horizontal member of a frame wall; ...

Pieces of wood placed on wall surfaces as fastening devices. The bottom member of the wall is the sole plate and the top member is the rafter plate.
Plenum ...

Bottom Plate: The 2x4s or 6s that lay on the subfloor upon which the vertical studs are installed. Also called the sole plate.
Bow: A curve, bend, warping or other deviation from flatness in glass or wood.

King Stud - The vertical "2 X's" frame lumber (left and right) of a window or door opening, and runs continuously from the bottom sole plate to the top plate.

The "2 by 4's or 6's" that lay on the subfloor upon which the vertical studs are installed. Also called the 'sole plate'.
Brace ...

Mudsill- Bottom horizontal member of an exterior wall frame which rests on top a foundation, sometimes called sill plate. Also sole plate, bottom member of interior wall frame.

The length of the cleats should be at least 12 inches, but can be as long as can be inserted into the opening. The ideal length would be long enough to reach the sole plate... the bottom board on the wall that is fastened to the floor.

Sole plate is bottom horizontal member of a frame wall. Top plate is top horizontal member of a frame wall supporting ceiling joists, rafters or other members.

Window cripple-Short studs placed between the header and a top plate or between a sill and sole plate.
Window frame/jamb-The top and sides of the window, to include the wall framing and the actual window frame and trim.

See also: Plate, Wall, Floor, Building, Window